Hydraulic support hydraulic valve life is very low, foreign solutions and ways to improve the system's filtration accuracy and improve the quality of emulsion, but with little success. This article analyzes the development process of the seal pair of the holder valve, discusses the relationship between the material of the seal pair and the sealing performance. It is pointed out that the sealing technology is the key to improve the service life of hydraulic valve in hydraulic support. Hydraulic support is a supporting device in coal mining machinery. After overhauling it, it can be used for five years underground. However, the service life of various hydraulic valves in hydraulic support is very low. For a long period of 3 months and a short period of only a few weeks, Foreign solutions and ways to increase the filtration system to improve the quality and improve the quality of the emulsion, but with little success. To a British hydraulic valve, for example, although the processing accuracy and filtration of the entire hydraulic system are relatively high, but because of low life expectancy, has been facing the elimination of our country. A main factor affecting the sealing performance of the hydraulic valve The main factor of damage to the sealing element is the working fluid impurities. These contaminants grind between sealing elements, causing the valve to leak. Therefore, foreign countries have put forward the corresponding level of hydraulic components, the filter should be the appropriate accuracy. They think that 5μM oil seal components, with filter accuracy of 3 / μM filter life expectancy than with 10μM increased 10 times. But the hydraulic support valve, the working environment is very poor. In coal mining face, tubing length of more than 1,000 meters, up to more than 4,000 connector socket, tank no special dust-proof facilities. Emulsion has a large number of floating impurities in the cylinder bottom and the valve cavity, leaving more coal, rock and iron filings. Intake valve plug and seat, due to more frequent opening and closing, high liquid flow, the seal will soon fail. It has proved very difficult to reduce the contaminating impurities in the hydraulic system of the scaffold. It has been envisaged to use a high-pressure filter at the emulsion pumping station while adding a small filter at the inlet of each scaffold. However, it was quickly blocked up at work, resulting in a stoppage. On the other hand, with the development of hydraulic support technology. The use of valve performance and valve life put forward higher requirements. At present, the life of a valve is measured using a total flow rate of the emulsion through the valve under test and the number of valve opening and closing operations, with a 120-mesh filter and a magnetic filtration device. But in fact the indoor type test and the actual results of underground work vary greatly. In many countries, formal tests have increased anti-pollution requirements. Some have incorporated proper pulverized coal in emulsion and some have added mechanical impurities. To this end, the need to use the new, anti-pollution ability, suitable for working conditions downhole seal. 2 history and status of the hydraulic valve seal material Leakage of the spool and valve seat contact surface, is the result of squeezing the working liquid molecules. Affect the sealing effect is the main reason for the spool and valve seat contact pressure, unevenness and pressure. When the valve core and the valve seat to P surface of the joint pressure, the working liquid molecules to force F squeeze, the sealing material will have elastic deformation. If the seal of the total resistance greater than the molecular repulsion, the seal effective, otherwise it will form a leak. Early hydraulic support, there is no other seal between the movement, is a metal direct contact seal, which requires seal contact surface match, with high processing accuracy, or must increase the sealing pair of bonding force, the contact surface of plasticity Deformation, blocking the leak channel
Pneumatic Connector
Pneumatic quick connector is a kind of quick connector which is mainly used for air piping and pneumatic tools. It can connect or disconnect the pipeline without tools. When the connector is not connected - when the parent's ferrule moves to the other end, the stainless steel ball will automatically roll outward, and the daughter will be disconnected under the action of the common valve spring force of the parent and the daughter, and the daughter and the parent's valves will be closed respectively, The fluid flow is blocked instantaneously.
Purpose and features editing voice
The quick connector is suitable for the connection of pneumatic pipeline, compressed air and nitrogen, and the working position where the pipeline can be loaded and unloaded frequently, such as the operation of pneumatic tools in the assembly line. It can also be used in hydraulic machinery, chemistry, ship piping, etc.
Scope of application editing voice
Air pipe, air compressor, grinder, air drill, impact plate hand, air transport screwdriver and other pneumatic tools for quick connection.
Note edit voice
1. Please do not use it for any purpose other than quick fluid connector.
2. Please don't use it for other fluids.
3. Please do not connect with the quick fluid connector made by other company.
4. Do not exceed the maximum pressure when using.
5. Do not use outside the temperature range to prevent the sealing material from wearing or leaking.
6. Do not hit, bend or stretch artificially to prevent damage.
7. Do not use it in places mixed with metal powder or sand dust to prevent poor work or leakage.
8. If foreign matters are attached, it will cause poor work or leakage.
9. Do not remove the quick coupling.
Pneumatic Connector, Plastic Pneumatic Connector, Pneumatic Quick Connector
Glove Industry Co.,Ltd. , https://www.glovemech.com