Sliding body experiment of smaller modal gear
The gear device for the test gear device test is a small gear reducer (the solid lubricant molybdenum disulfide is cleaned before the test), and the speed control device is connected, the speed regulation range is 01500r/min; the use voltage is 220V. 50Hz AC.
The main functions of the noise meter used in the test of the noise tester are: 1 frequency enhancement characteristics: A and C, where: A weighting refers to the measured human-induced noise, and C weighting refers to the measured mechanical noise; o Display accuracy: can be accurate to 011dB, twice per second; measurement range: 35130dB.
Evaluation was made from adhesion. It can be seen from the test results obtained that CX4/375AU, NBU15, NBU52 and SL-FMG-2 have better adhesion and can be firmly adhered to the running gear without being entangled. The brushed phenomenon of the gear; while the KS64, EM50L, FMG389, F1M1G.NO.2 and GA352P are not pulled out when the gear rotates, but they form a not too long filamentous grease when the gear is running. The belts, so their adhesion can only be said to be general.
The astringency of the grease used for the test was evaluated. The astringency of the grease refers to the place where the grease in the meshing zone is squeezed out when the two teeth are engaged, but this is temporary. After the meshing, the grease will slowly return to the mesh before the next meshing. The condition is such that there is always grease in the meshing area of ​​the teeth, thereby avoiding direct contact of the meshing teeth; we call this characteristic of the grease astringent.
From the case where the grease is squeezed to the surface of the tooth and the edge of the tooth during the test, the convergence of CX4/375AU is better, and the convergence of NBU15, NBU52 and SL-FMG-2 is general, and the other few fats. The convergence is relatively poor, because the amount of grease accumulated on the edges of the teeth when using the test 1 is large and the grease is scooped out.
The effect of noise reduction of various greases was evaluated. An important role of lubrication is noise reduction. Therefore, this test also uses the noise reduction effect as an evaluation index for grease. A noise meter was used in this test to test the value of the noise of the gear when adding grease and without adding grease. Evaluation is now made from the difference in noise values.
Since the nine kinds of greases have undergone certain changes in the surrounding environment during the test, they were evaluated separately from each part. The noise reduction effects of the greases tested in the first part are arranged as follows from high to low: CX4/375AU>SL-FMG.NO.2>GA352P>FMGNO.2>FMG389. The fat tested in the second part The noise reduction effect is also arranged from high to low: KS64>NBU52>NBU15>EM50L.
Conclusion Through the above tests and analysis, it can be known that: (1) Grease can better lubricate small gears. However, most of the lubrication of gears is currently achieved by the use of lubricating oil. (2) With the use of small open gears in mechanical instruments, small household electrical appliances, robotic transmission joints and other equipment, the application of grease in the lubrication of small gears will be valued.
Transfer trolley, an motor driven factory transport vehicle. It has the advantage of simple structure, easy maintenance, large carrying capacity and less pollution. Widely used in machinery manufacturing and metallurgical plant, cooperate with cranes to transport heavy loads inside workshop. They can be divied in many different types as shown below:
· KPT type transfer trolley is powered by the cable laid on the ground directly. For its simple structure, the price is more competitive. While the distance is often limited in 100 meter.
· KPJ type transfer trolley is powered by the cable from the cable reel. With the cable reel, the moving distance is improved to 200 meter compared with the KPT type.
· KPX type transfer trolley is powered by the storage battery, more flexible and safe. While the capacity and the duty group are all affected by the storage battery. Especially, the price and the life span of the bettery is also an important issure.
· KPC type transfer trolley is powered by the slide wire along the rail, so the moving distance is unlimited. The slide wire is the key point and also the weakest link.
· KPD/PKDZ type transfer trolley is powered by the low voltage DC power from the rail. Powered by the rail, the system is more reliable compared with the KPC type; The sytem is also more complicated and expensive.
Title Transfer,Plate Transfer,Car Title Transfer,Transfer Car Ownership
XINXIANG DEGONG MACHINERY CO., LTD. , https://www.degongcrane.com