Several small details must be checked before the sprinkler leaves the factory
Careful customers will pay attention to the appearance details of some sprinklers after they purchase the sprinkler. Many of these details will be ignored by the manufacturer's technicians. Actually, this is not a problem that affects performance. As the buyer's heart, it must be hope. Sprinklers bought for their own money are perfectly harmless. In any case, as a sprinkler vehicle manufacturers must be perfect for the customer, sprinkler truck manufacturers special-purpose vehicles combined with years of experience, summed up the following several more common sprinkler conversion details.
1, the number of beams is blurred.
Sprinkler beam number is also called the beam code, referred to as VIN number, which is uniformly engraved on the outside surface of the longitudinal beam on the right front wheel of the frame. Due to the remanufactured spray paint, many girders are covered with the same color of black paint, making it difficult to find the sprinkler on the license plate. Sometimes impatient customers will ask: Are you using an authentic original chassis? Although you can rest assured that this point, as a large sprinkler manufacturers , the chassis is directly from the Dongfeng, Futian company to mention the goods, which is the quality assurance must be done.
2. The nameplate of the sprinkler vehicle is not fixed as required.
The sprinkler car's nameplate is equivalent to the car's ID card. It is a small aluminum box with the car's exterior dimensions, manufacturer, production date, and power. The card requires permanent fixation and is forbidden to remove except maintenance. Should be riveted to the designated location on the cab of the sprinkler truck as required by the country.
3. The total mass and load quality parameters of the vehicle are not painted outside the cab of the sprinkler. Tank cars also need to spray the tank transport medium and volume.
There are also non-standard pastes such as reflective logos, sprinklers that exceed the total mass, and vehicle guard fence settings that do not match standards. These large and small problems need to be confirmed before sending the car. It is best to photograph and archive the sprinkler every time. Before the car is out of the vehicle, it must be weighed once. The sales manager must have a good idea. In addition, the delivery driver must be required to check whether the vehicle tool is complete before departure, whether the vehicle information is complete and whether the temporary license is affixed as required. It is best to get insurance for sprinklers and drivers in off-site vehicles. As the saying goes, “I am not afraid of 10,000.
Finally, read the instructions carefully before using the sprinkler. Operating strictly according to the requirements of use is an important guarantee for using a sprinkler.
Aluminum Coolers for Compressor, Aluminum plate&bar heat exchangers (oil cooler, Air Cooler /Charge Air Coolers,Compressor Coolers, Water Cooler and Combi Coolers ) have been widely applied for all kinds of compressor including air compressors, LNG-BOG recovery compressor, CNG compressor and more.
Heat Exchanger for Air Dryer, The heat exchangers transfer heat between a cold medium and the damp compressed air. This cools the compressed air to a pressure dew point. If required the condensation generated by the cooling process is collected in a condensation chamber integrated into the heat exchanger and continually drained off.
Advantage:
Compact, Lightweight, High Efficient Heat Transfer
Customize High Quality Aluminum plate-fin cooler upon your drawing, sample or parameter requirement.
FAQ
Q1:Could you customize oil cooler/heat exchanger?
We can manufacture plate-fin heat exchanger/oil cooler /intercooler according to your drawings or samples or parameter requirement.
Q2: I want to buy your products, how can I pay?
A :You can pay via T/T
Q3: How can you guarantee the quality?
A: One year's warranty against B/L date.
Q4: If we don`t find what we want on your website, what should we do?
A: You can email us the descriptions and pictures of the products you need, We will check whether we can make it.
Q5: Can we buy samples of each item for quality testing?
A: Yes, we understand quality test is important and we are glad to send the sample for quality testing.
Q6: What is the lead time?
A: Normal : Plate-fin heat exchanger for 2~3 weeks; Tube&fin or stacked layer coolers for 5 weeks. Exact time upon negotiation
Air Compressor Oil Cooler,CNG Compressor Aluminum Cooler,Compressor Gas Cooler and Radiator Assembly,Compressor Coolers,Charge Air Coolers
Wuxi Better Technology Co., Ltd , https://www.btheatexchanger.com